The H-60 Brake/Strut/Damper Servicing Kit (BSD-60-AA) has the correct components to perform all hydraulic servicing tasks on the aircraft, in one all-inclusive accountable and portable kit, eliminating the need to search for all components needed to service. Each hydraulic hose assembly has been re-engineered from the ground up with the end user in mind, simplifying and accelerating each procedure.
EAA Tools offers Special Purpose Kits (various PNs) for H-60/S-70, each of which comprise a selection of system-specific special tools. Each kit targets a specific system and may be purchased, inventoried, and checked out as a single line-item for the servicing of a particular aircraft system.
Bearing and Bushing Kit (BBK-60-AA) for A/L/M contains key peculiar hand tools to service the bearings and bushings throughout the aircraft. Kit contents:
Transmission Service Kit (XMSKA-60-AA for A Models, XMSKLM-60-AA for L/M Models) for A/L/M contains key peculiar hand tools to service the main transmission of the aircraft. Kit contents:
Landing Gear Kit (LGK-60-AA) for A/L/M contains key peculiar hand tools to service the main landing gear and tail wheel of the aircraft. Kit contents:
Blade Removal and Install Kit (BAK-60-AA) for A models contains key peculiar hand tools to remove and install the main rotor blades. Kit contents:
Main Rotor Head Kit (MRK-60-AA) for A/L/M contains key peculiar and hard-to-find commercial hand tools to service the main rotor head of the aircraft. Kit contents:
Tail Rotor/Pylon Kit (TRPKAL-60-AA for A/L Models, TRPKM-60-AA for M Models) for A/L/M contains key peculiar and hard-to-find commercial hand tools to service the tail rotor and tail pylon of the aircraft. Kit contents:
Our newest addition, the EAA Tools H-60 237WP Peculiar Tool Kit (PTK-60-AA), or PTK, provides a procurable and inventoriable tool kit to replace the issued PTK, which is no longer commercially available. The PTK comprises specialized field-level items and tools compatible with the specifications found in the UH-60 series Technical Manuals (TM1-1520-237-23&P). EAA Tools has updated each tool in the PTK with key usability and durability improvements not found in the TM nor the previously marketed version.
| IMAGE | P/N | DESCRIPTION | FUNCTION | QTY |
|---|---|---|---|---|
 | SLP-60-AA | Stabilator Position Sensor Limit Switch Lockpin | Calibrate the cockpit indicator and stabilator limit switches. | 1 |
 | PST1-60-AA | Pitot-Static Power Cable Assembly | Provide 28VDC power to the pitot-static tester. | 1 |
 | PST2-60-AA | Pitot-Static Tee Air Hose Assembly (AFCS) | Perform multiple system air data tests (H-60 adapters for the pitot static tester). | 1 |
 | PST3-60-AA | Pitot-Static Tee Air Hose Assembly (Pitot-Static/IFF) | Perform multiple system air data tests (H-60 adapters for the pitot static tester). | 1 |
 | BDTB-60-AA | Blade De-Ice Test Block | Brace and isolate the blade de-ice test block. | 1 |
 | SPTH-60-AA | Miscellaneous Switch Panel Test Harness | Test the de-ice system. | 1 |
 | FP-60-AA | Input Module Flange Puller | Remove the flange from the input module. | 1 |
 | BDTH-60-AA | Blade De-Ice Test Harness (WP 2165) | Test the de-ice system. | 1 |
 | PFAL-60-AA | H-60A/L Protractor Fixture | Aid in measuring the Stabilator angle (A/L models). | 1 |
 | PFM-60-AA | H-60M Protractor Fixture | Aid in measuring the Stabilator angle (M models). | 1 |
 | SIT-60-AA | Seal Installation Tool Set | Install seals for input module, main GB, intermediate GB I/O, and tail rotor GB output. | 1 |
 | SSBP-60-AA | Swashplate Scissor Bearing Press | Remove and install swashplate and scissor bearings. | 1 |
 | SBRT-60-AA | Stabilator Bolt Removal Tool | Remove a stuck right hand/left hand stabilator hinge fitting bolt. | 1 |
 | TRQD-60-AA | Tail Rotor Cable Quick Disconnect Wrench | Quickly loosen or tighten tail rotor cables. | 1 |
 | PBRW-60-AA | Tail Rotor Pivot Bearing Replacement Wrench | Remove and install the tail rotor pivot bearing. | 1 |
 | OPIT-60-AA | Oil Pump Installation Tool | Assist in installing the oil pump. | 1 |
 | ZBAR-60-AA | Main Module Hardware Installation Tool | Torque main module hardware. | 1 |
 | WDGE-60-AA | Wedge, 30/60/90 degree | Perform functional checks on gyros and accelorometers (see WP). | 1 |
 | DBW-60-AA | Drag Beam Wedge, 5/85/90 degree | Perform functional checks on gyros. | 1 |
 | PCLT-60-AA | Pitch Control Link Tool | Align elastomeric bearings on the main rotor pitch control rods. | 1 |
 | RBTA-60-AA | AFT Main Mod Mount Bolt Torque Adapter | Perform torque checks on aft main module bolts without disassembly. | 1 |
 | FBBW-60-AA | Fixture Brace for Bifilar Weights Bolts | Assist in applying torque to the bifilar weight 15/16” and 1-1/16” bolt heads. | 1 |
 | SBCAT-60-AA | Spindle & Blade Cuff Washer Alignment Tool | Align spindle and blade cuff washers for reliable and permanent bonds. | 1 |
 | EAA-PTK-PKG | Protective Case and Custom Foam | Impact and environmental resistant protective carrying case, including custom foam. | 1 |
The Flight Controls Rigging System (FCRS-60-AA) for H-60 by EAA Tools is a two-part kit, including a full pin set (FCRK-60-AA) as well as an accessories kit (FCRA-60-AA). Together, they comprise a complete solution for rigging the H-60 flight controls in a fast, safe, and predictable manner. The FCRS-60-AA is backward-compatible with legacy and discontinued products provided by other manufacturers, but contains key improvements in quality and usability to provide a superior user experience.
The FCRK-60-AA is a complete set of the rig pins required to perform an H-60 flight control rig. This product is backward compatible with the legacy version. EAA has improved the F-pin to be compatible with all A/L/M model aircraft.
| IMAGE | P/N | DESCRIPTION | ACCEPTABLE NSN CROSS | QTY |
|---|---|---|---|---|
 | EAA-80-063 | Pin, Ground, Safety (Upper Broom Closet) | 1730-01-143-3365 | 2 |
 | EAA-80-064 | Pin, Ground Safety (Lower Broom Closet) | 1730-01-140-8829 | 4 |
 | EAA-42-041 | Pin, Pitch Lock (Walking Beam) | 5315-01-118-1889 | 2 |
 | EAA-42-042 | Pin, Pitch Lock (Bellcrank Support) | 5315-01-210-7276 | 1 |
 | EAA-80-042 | Pin, Ground Safety (Yaw Pedal Adjuster) | 1730-01-140-8827 | 2 |
 | EAA-80-070 | Pin, Ground Safety (Stabilator Switch and Synchro) | 1730-01-141-7638 | 1 |
 | EAA-80-068 | Pin, Ground Safety (Mixer, Yaw) | 1730-01-140-8831 | 1 |
 | EAA-80-043 | Pin, Ground Safety (Torque Shaft) | 1730-01-141-7637 | 4 |
 | EAA-80-065 | Pin, Ground Safety (Cyclic Stick Pitch) | 1730-01-147-9979 | 2 |
 | EAA-78-103 | Block, Rigging, Main Rotor Head (Damper Blocks) | N/A | 4 |
 | EAA-80-062 | Pin, Ground Safety (Yaw/Servo Control) | N/A | 2 |
 | EAA-80-044 | Pin, Ground Safety (Pitch/Roll Servo) | 1730-01-125-0783 | 2 |
 | EAA-80-066 | Pin, Ground Safety (Cyclic Stick Roll) | 1730-01-140-8830 | 2 |
 | EAA-80-071 | Pin, Ground Safety (Tail Rotor Servo) | 1730-01-140-8832 | 1 |
 | EAA-80-046 | Pin Assy, Rigging (Mixer) | 1730-01-125-5383 | 1 |
| EAA-FCRK-PKG | Case, Foam, Inventory Sheet | N/A | 1 |
The FCRA-60-AA is a kit of rigging accessories to compliment the pin set. Completing a rig is possible without this product, but adding it to your tool portfolio will ensure rigging is completed efficiently and effectively.
| IMAGE | P/N | DESCRIPTION | ACCEPTABLE NSN CROSS | QTY |
|---|---|---|---|---|
 | LCG-60-AA | Low Collective Gauge | Measure and verify the co-pilot's low collective stop bolt. | 1 |
 | PSSG-60-AA | Primary Servo/Swashplate Gauge | Measure and verify the piston extension of the primary servo and uniball. | 1 |
 | NOM-60-AA | Nominal Trammel | Set control rods to nominal lengths prior to installation, greatly accelerating rigging. | 1 |
 | FCBP-60-AA | Flight Control Bearing Press | Remove, install, and inspect bearings at ends of flight control rods. | 1 |
 | SCC-60-AA | Spring Cylinder Clamp | Prevent tail rotor spring cylinders from compressing when disconnected. | 2 |
 | DPLP-60-AA | Digital Protractor Leveling Plate | Level a digital protractor with an expanded base. | 1 |
 | TRCR-60-AA | Tail Rotor Control Rod Tool | Set tail rotor control rod to its nominal measurement. | 1 |
 | PAT-60-AA | PCL Alignment Tool (6.5") | Align the LDS and PAS without the FOD risk of the standard procedure. | 1 |
 | RCRPA-60-AA | Roll/Coll Pin Alignment Tool | Align and verify straight roll/coll bracket to prevent common rigging errors. | 1 |
 | LPAT-60-AA | LDS/PAS Alignment Tool (3.5") | Align the power control levers without the FOD risk of the standard procedure. | 1 |
 | TRK-60-AA | Tail Rotor Cable Turnbuckle Tool | Perform turnbuckle adjustment to set up tail rotor cable tension. | 2 |
| TRQD-60-AA | Tail Rotor Cable Quick Disconnect Tool | Quickly loosen or tighten tail rotor cables. | 1 |
| EAA-FCRA-PKG | Case, Foam, Inventory Sheet | Impact and environmental resistant protective carrying case, including custom foam. | 1 |
EAA Tools offers the H-60/S-70 Series Comprehensive Expeditionary Kit (EXP-60-AA) to support the new emphasis on Expeditionary Aviation Operations. The EXP, a deployable package comprising a selection of carefully chosen peculiar hand tools, empowers the soldier/end-user to operate with limited external resupply while reducing mobility footprint. The kits use MIL-SPEC Pelican 1730 Protector Transport cases with embedded roller wheels, which are watertight, crushproof, and dustproof. A full EXP can be transported in the space of two H-60 seats, providing a force multiplier and force projection. Using the EXP, a line company has the capability to operate autonomously for an extended period with minimal support, capable of performing most (90%) heavy maintenance tasks while providing operational readiness for the short term until heavy maintenance support arrives. The EXP is fully deployable, portable, and inventoriable for accountability.
Pulling a Tail Rotor Pitch Beam used to be a frustrating experience with an obsolete and clunky tool. Now, with the Pitch Beam Puller (PBP-60-AA) for UH-60 and H-60 A/L/M by EAA Tools, pitch beams are removed safely, quickly, and with no hassle.
Current field-expedient method is not standardized to quickly and accurately measure inspection gap tolerances and limits for the De-Ice stationary and rotating distributor, the IVHMS Tail Rotor Magnetic Pick-Up Interrupter, and the retention plate mounting bolt thread exposure limits.
A simple hand-carry inspection tool can improve the inspection efficiency of these components. New design is engineered to be small, accurate, and inclusive of all critical measurements.
The TRAIT-60-AA serves as a one-piece, multiple function inspection guide to effectively check tolerances in the De-Ice stationary and rotating distributor and the IVHMS Tail Rotor Magnetic Pick-Up Interrupter gap tolerances. It can then be used to quickly check the retention plate mounting bolt thread exposure tolerances.
The H60 Main Rotor Blade (SP-60-AA) Spindle Puller is used to effectively pull the spindle free from the Main Rotor Hub Assembly. As a one-person task, it is designed to control the removal of the spindle, even if stuck due to corrosion or abrasion.
Every Spindle Puller is delivered in a Pelican case with custom MIL-spec foam cushioning, allowing for easy and safe transportation or storage.
The Spindle Puller is comprised of a single base plate with three ACME driver assemblies threaded to hex nut holders that push against the main rotor hub. The driver assembly rods have driver feet that allow to for self-articulation and adjustment when pushing against the hub. Spindle stainless steel cross pins with retaining plungers are inserted into the main rotor blade cuff lugs allowing the tool to safely pull the spindle free from the hub as it pushes against the base plate. A safety retention nylon webbing attached to the spindle plate, using a safety retainer puck inserted into the hub spindle inspection port, catches the spindle once it is freed, preventing it from being dropped.
The EAA Tools Blade & Spindle Washer Alignment Tool (previously known as the Blade & Spindle Cuff Alignment Tool) is an off-the-shelf, all-in-one replacement for a) WP 2014 00, Figure 43, b) WP 1602 00, Figure 32, and c) WP 1602 00, Figure 200. The EAA Tools Blade & Spindle Washer Alignment Tool completes both blade and spindle washer alignment/replacement tasks with notable performance, usability, and quality improvements over the standard design.
The UH-60 Chip Detector Removal Tool is used to shut off flow, remove, and install the main module sump chip detector and strainer assembly. A compact, functional design greatly reduces the chance of component damage and enables a single operator to perform the task.
The UH-60 Chip Detector Removal Tool is designed to fit precisely on the chip detector sleeve and rotate the strainer to the ON or OFF flow position. The tool’s prying function is then used to ease chip detector away from transmission sump, breaking the hydraulic suction lock. The operator uses only one hand to operate the UH-60 Chip Detector Removal Tool, allowing the other hand to be used to collect draining oil safely and easily. Removal of the chip detector/strainer is performed quickly, easily, and safely; no work package tool is available in the IETM that can perform this task.